- importsource = "01624075-2007-07.txt"
- Artículo:
Chapter Reports
- Resumen:
South Florida Chater; India Chapter
- Página:
22
- Publicación:
Concrete International
- Volúmen:
29
- Número:
7
- Periodo:
Julio 2007
- ISSN:
01624075
- SrcID:
01624075-2007-07.txt
- Documento número 812566
- Actualizado el martes, 10 de julio de 2018 10:46:15 a. m.
- Creado el martes, 10 de julio de 2018 10:46:15 a. m.
- Enlace directo
- Artículo:
Technical committee chairs appointed
- Página:
26
- Publicación:
Concrete International
- Volúmen:
29
- Número:
7
- Periodo:
Julio 2007
- ISSN:
01624075
- SrcID:
01624075-2007-07.txt
- Documento número 812567
- Actualizado el martes, 10 de julio de 2018 10:46:15 a. m.
- Creado el martes, 10 de julio de 2018 10:46:15 a. m.
- Enlace directo
- Artículo:
Wall Bracing to Slab-on-Ground Floors
- Autor:
David L. K elly
- Resumen:
As tilt-up wall panels become taller, temporary erection bracing reactions increase. If these reactions are applied to a floor slab designed for service loads only, the slab may be too thin to resist the sliding and uplift components.
- Página:
29
- Publicación:
Concrete International
- Volúmen:
29
- Número:
7
- Periodo:
Julio 2007
- ISSN:
01624075
- SrcID:
01624075-2007-07.txt
- Documento número 986310
- Actualizado el martes, 10 de julio de 2018 11:06:00 a. m.
- Creado el martes, 10 de julio de 2018 11:06:00 a. m.
- Enlace directo
- Artículo:
A Helicoidal Concrete Ramp
- Autor:
Gilbert H. Béguin
- Resumen:
Curved ramps typically have symmetric sections with outer and inner edges equally supported, making torsion effects minimal. The ramp described in this article, however, was supported only at discrete points around the outer edge, producing significant torsion that was further complicated by the ramp’s asymmetrical, open cross section.
- Página:
37
- Publicación:
Concrete International
- Volúmen:
29
- Número:
7
- Periodo:
Julio 2007
- ISSN:
01624075
- SrcID:
01624075-2007-07.txt
- Documento número 986311
- Actualizado el martes, 10 de julio de 2018 11:06:00 a. m.
- Creado el martes, 10 de julio de 2018 11:06:00 a. m.
- Enlace directo
- Artículo:
Designing to Minimum Concrete Dimensions
- Autor:
Javed B. Malik
- Resumen:
Structural engineers often strive to optimize the cost of structures by minimizing the sizes of structural members. Minimizing the size of concrete members, however, can lead to unintended consequences that may defeat the global goal of minimizing overall construction cost. It’s therefore important to step back and consider how the individual components interact.
- Página:
44
- Publicación:
Concrete International
- Volúmen:
29
- Número:
7
- Periodo:
Julio 2007
- ISSN:
01624075
- SrcID:
01624075-2007-07.txt
- Documento número 986312
- Actualizado el martes, 10 de julio de 2018 11:06:00 a. m.
- Creado el martes, 10 de julio de 2018 11:06:00 a. m.
- Enlace directo